Before Your Start

In the Box

2x Bindings
2x Offset Mounting Disks
8x Screws

Tools Needed

Size 3 Phillips Head Screwdriver (PH3)
2x Offset Mounting Disks
8x Screws
1x Leash

Mount Your Bindings

1. If your binding model has a full-length footbed, remove it to access the mounting disk. Fuse model requires unscrewing.
2. Orient the mounting disk according to your snowboard’s insert type (four-hole or Channel). Flip it 180° to reduce either toe or heel overhang.
2x Offset Mounting Disks
8x Screws
1x Leash
3. Rotate the disk to your desired angle. Each notch is 3°.
4. Mount the binding to your snowboard using the supplied screws. Ratchets should be on the outside of your foot when in the binding.
2x Offset Mounting Disks
8x Screws
1x Leash
5. Place boot in binding and check it’s centered over the board. If not, loosen the screws and re-adjust the disk. (see point 2).
6. Replace the footbed (where applicable).
2x Offset Mounting Disks
8x Screws
1x Leash

Adjust Your Straps

1. Loosen the straps on both sides and place the boot into the binding.

Fusion Straps are designed to sit over the top of the boot. Hybrid Straps feature a separate toe strap that should go over the corner of the boot.
2. Center the straps over the boot.
2x Offset Mounting Disks
8x Screws
1x Leash
3. Lock down the QuickSet buckles on the inside, and adjust the Locking System Ratchets until the straps are snug but not too tight.
4. Set your strap position.

Models featuring LSR 2.0 will lock automatically as soon as you stop adjusting the ratchet.

If you have a model with the original LSR buckles, lock in your settings by pushing down the lever on each ratchet.
2x Offset Mounting Disks
8x Screws
1x Leash

Customize Your Highback

1. Loosen the straps on both sides and place the boot into the binding.

Fusion Straps are designed to sit over the top of the boot. Hybrid Straps feature a separate toe strap that should go over the corner of the boot.
2. To adjust your highback’s forward lean: spin the dial on the Snaplock.
2x Offset Mounting Disks
8x Screws
1x Leash
2x Offset Mounting Disks
8x Screws
1x Leash
1. The highback on NX2 and Fuse models can also be mounted further forward or back to fine-tune heel/toe overhang. Remove screws and nuts before fine-tuning, and replace before tightening.
2. To adjust your highback’s forward lean: spin the dial on the Snaplock.
2. Center the straps over the boot.
2x Offset Mounting Disks
8x Screws
1x Leash

Using Your Bindings

Speed Entry

1. Pull down on the Snaplock.
2. Recline the highback.
2x Offset Mounting Disks
8x Screws
1x Leash
3. Slide boot in (front foot first).
4. Pull up the highback.
2x Offset Mounting Disks
8x Screws
1x Leash
5. Flip the Snaplock closed.
4. Pull up the highback.
2x Offset Mounting Disks
8x Screws
1x Leash

Exit

1. Pull down on the Snaplock.
2. Recline the highback.
2x Offset Mounting Disks
8x Screws
1x Leash
3. Slide boot out (rear foot first).
2. Maintain pressure on the lever while pulling your foot up against the ankle strap to release the mechanism.
2x Offset Mounting Disks
8x Screws
1x Leash

Tips

• On flatter areas, face down the hill (heel edge) before entry.

• On steeper areas, face up the hill (toe edge) before entry.

• If the conditions demand it, you can also use the ratchets to get in and out – just like a regular binding.
 

Attaching the Leash

Attach the leash to your front binding here. Connect it to your boot every time you go riding.
Use a screwdriver to loosen the inner screw, slide the block down to increase the angle, or up to reduce it, then re-tighten the screw.
2x Offset Mounting Disks
8x Screws
1x Leash

Warning

WARNING: Vibration, temperature changes and board flex can loosen mounting screws and other hardware. Ensure all screws are tight before every riding session, and check ratchets and components are in working order.